2002–2006 MINI Cooper S Wheel & Tire Fitment Guide

R53 generation, Base. 4x100 bolt pattern, stock 16×6.5 ET48 on 195/55R16. Compare 2 popular upgrades or try your own size.

Specs

Bolt pattern4x100
Center bore56.1 mm
Lug threadM12x1.5
Reference trimBase
Stock wheel16×6.5 ET48
Stock tire195/55R16
Stock overall diameter24.44 in

Calculator

Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.

Wheel
in
in
mm
Tire
mm
%

The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.

Custom vehicle measurementsOptional

Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.

  • Park on level ground at normal ride height, wheels straight.
  • Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
ABCD

Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.

mm

Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.

mm

Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.

mm

Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.

mm

Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.

Front section
StrutBrakeFender130.6Backspacing34.5 Frontspacing
Three-quarter view
195/55R16
New setupCurrent setupFender and strut are drawn 12 mm outside and 28 mm inside your current setup. Add your own measurements for real clearance.
Stock

Factory wheel and tire size for this car.

Poke
0mm
Wheel face stays where it is.
Inner clearance
0mm
Same room to the suspension.
Overall diameter
0%
0 in, within ±3%.
Speedo reads 60
60mph
Your actual speed.
VehicleMINI Cooper S Base
Bolt pattern4x100Hub bore56.1 mm
Current16×6.5 ET48, 195/55R16New16×6.5 ET48, 195/55R16

Shop this setup

I may earn a commission from links on this page.

Searches use the new setup above. Check the bolt pattern, offset and center bore on each listing before you buy, and use hub-centric rings if the wheel's bore is larger than your hub.

Notes

Questions

What bolt pattern does a 2002–2006 MINI Cooper S use?

The 2002–2006 MINI Cooper S uses a 4x100 bolt pattern with a 56.1 mm center bore and M12x1.5 lug threads.

What size wheels and tires are stock on the 2002–2006 MINI Cooper S Base?

The 2002–2006 MINI Cooper S Base came with 16×6.5 ET48 wheels and 195/55R16 tires, about 24.4 inches in overall diameter.

How far does a 17×7.5 ET45 wheel stick out on a 2002–2006 MINI Cooper S?

On the 2002–2006 MINI Cooper S, compared with the stock 16×6.5 ET48, a 17×7.5 ET45 sits 15.7 mm further out at the outer lip and 9.7 mm closer to the suspension at the inner barrel.

Which 2002–2006 MINI Cooper S wheel and tire upgrade keeps the speedometer most accurate?

Of the 2002–2006 MINI Cooper S upgrades listed here, 17×7 ET48 · 205/45R17 is closest to the stock 195/55R16, changing overall diameter by −0.7%. At an indicated 60 mph you would actually be doing 59.6 mph.

Do aftermarket wheels need hub-centric rings on a 2002–2006 MINI Cooper S?

The 2002–2006 MINI Cooper S's hub bore is 56.1 mm. Wheels machined to exactly 56.1 mm center on the hub directly; wheels with a larger bore need 56.1 mm hub-centric rings to avoid vibration.

Also on 4x100

These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.

VehicleGenerationBolt patternHub bore
1990–1997 Mazda MX-5 MiataNA4x10054.1 mm
2016+ Mazda MX-5 MiataND4x10054.1 mm