2016–2024 MINI John Cooper Works Wheel & Tire Fitment Guide
F56 generation, Hardtop. 5x112 bolt pattern, stock 17×7 ET54 on 205/45R17. Compare 2 popular upgrades or try your own size.
Specs
| Bolt pattern | 5x112 |
|---|---|
| Center bore | 66.6 mm |
| Lug thread | M14x1.25 |
| Reference trim | Hardtop |
| Stock wheel | 17×7 ET54 |
| Stock tire | 205/45R17 |
| Stock overall diameter | 24.26 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | MINI John Cooper Works Hardtop | ||
|---|---|---|---|
| Bolt pattern | 5x112 | Hub bore | 66.6 mm |
| Current | 17×7 ET54, 205/45R17 | New | 17×7 ET54, 205/45R17 |
Popular upgrades
Each size compared with the stock 17×7 ET54, 205/45R17.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| Flush 17×817×8 ET45, 215/45R17 | +21.7 mm | −3.7 mm | +1.5% | 60.9 mph | |
| Aggressive 18×8.518×8.5 ET40, 215/40R18 | +33 mm | −5.1 mm | +2.1% | 61.3 mph |
Shop this setup
I may earn a commission from links on this page.
Searches use the new setup above. Check the bolt pattern, offset and center bore on each listing before you buy, and use hub-centric rings if the wheel's bore is larger than your hub.
Notes
- The JCW's Brembo front brakes do not clear many 17-inch wheels made for the Cooper S. Buy wheels listed as clearing the JCW brakes; whether they clear depends on spoke design.
- Uses M14x1.25 conical-seat wheel bolts, not studs.
- The factory 18-inch option uses 205/40R18.
- An 18×8.5 at an effective ET40 (ET45 plus a 5 mm spacer) needs the rear plastic fender lips trimmed. Tires wider than 225 are very hard to fit at the front.
Questions
What bolt pattern does a 2016–2024 MINI John Cooper Works use?
The 2016–2024 MINI John Cooper Works uses a 5x112 bolt pattern with a 66.6 mm center bore and M14x1.25 lug threads.
What size wheels and tires are stock on the 2016–2024 MINI John Cooper Works Hardtop?
The 2016–2024 MINI John Cooper Works Hardtop came with 17×7 ET54 wheels and 205/45R17 tires, about 24.3 inches in overall diameter.
How far does a 18×8.5 ET40 wheel stick out on a 2016–2024 MINI John Cooper Works?
On the 2016–2024 MINI John Cooper Works, compared with the stock 17×7 ET54, a 18×8.5 ET40 sits 33 mm further out at the outer lip and 5.1 mm closer to the suspension at the inner barrel.
Which 2016–2024 MINI John Cooper Works wheel and tire upgrade keeps the speedometer most accurate?
Of the 2016–2024 MINI John Cooper Works upgrades listed here, 17×8 ET45 · 215/45R17 is closest to the stock 205/45R17, changing overall diameter by +1.5%. At an indicated 60 mph you would actually be doing 60.9 mph.
Do aftermarket wheels need hub-centric rings on a 2016–2024 MINI John Cooper Works?
The 2016–2024 MINI John Cooper Works's hub bore is 66.6 mm. Wheels machined to exactly 66.6 mm center on the hub directly; wheels with a larger bore need 66.6 mm hub-centric rings to avoid vibration.
Also on 5x112
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2020+ BMW 3 Series | G20 | 5x112 | 66.6 mm |
| 2023+ BMW M2 | G87 | 5x112 | 66.6 mm |
| 2021+ BMW M3 | G80 | 5x112 | 66.6 mm |
| 2020+ Toyota GR Supra | A90/J29 | 5x112 | 66.6 mm |
| 2010–2016 Audi S4 | B8/B8.5 | 5x112 | 66.6 mm |
| 2015–2021 Mercedes-Benz C63 AMG | W205 | 5x112 | 66.6 mm |