1990–1996 Nissan 300ZX Wheel & Tire Fitment Guide
Z32 generation, Twin Turbo. 5x114.3 bolt pattern, stock 16×7.5 ET45 on 225/50R16. Compare 3 popular upgrades or try your own size.
Specs
| Bolt pattern | 5x114.3 |
|---|---|
| Center bore | 66.1 mm |
| Lug thread | M12x1.25 |
| Reference trim | Twin Turbo |
| Stock wheel | 16×7.5 ET45 |
| Stock tire | 225/50R16 |
| Stock overall diameter | 24.86 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Nissan 300ZX Twin Turbo | ||
|---|---|---|---|
| Bolt pattern | 5x114.3 | Hub bore | 66.1 mm |
| Current | 16×7.5 ET45, 225/50R16 | New | 16×7.5 ET45, 225/50R16 |
Popular upgrades
Each size compared with the stock 16×7.5 ET45, 225/50R16.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| Mild 17×817×8 ET40, 225/45R17 | +11.3 mm | −1.3 mm | +0.5% | 60.3 mph | |
| Rolled 17×917×9 ET25, 245/40R17 | +39 mm | +0.9 mm | −0.6% | 59.7 mph | |
| Flush 18×9.518×9.5 ET22, 245/40R18 | +48.4 mm | −2.4 mm | +3.5% | 62.1 mph |
Shop this setup
I may earn a commission from links on this page.
Searches use the new setup above. Check the bolt pattern, offset and center bore on each listing before you buy, and use hub-centric rings if the wheel's bore is larger than your hub.
Notes
- Staggered from the factory. Rear stock: 16×8.5 ET35 with 245/45ZR16. Non-turbo Z32s run 16×7.5 ET45 with 225/50R16 on all four corners.
- Wide rear wheels must clear the HICAS rear-steer arm; around 17×9 +30 is the commonly cited limit before the 275 rear tire contacts it.
- Some 17" wheels hit the twin-turbo front calipers, so check the spoke profile; at full lock, wider fronts can rub the arch liners behind the intercoolers.
- Lug nuts are M12x1.25 with a 66.1 mm hub bore.
Questions
What bolt pattern does a 1990–1996 Nissan 300ZX use?
The 1990–1996 Nissan 300ZX uses a 5x114.3 bolt pattern with a 66.1 mm center bore and M12x1.25 lug threads.
What size wheels and tires are stock on the 1990–1996 Nissan 300ZX Twin Turbo?
The 1990–1996 Nissan 300ZX Twin Turbo came with 16×7.5 ET45 wheels and 225/50R16 tires, about 24.9 inches in overall diameter.
How far does a 18×9.5 ET22 wheel stick out on a 1990–1996 Nissan 300ZX?
On the 1990–1996 Nissan 300ZX, compared with the stock 16×7.5 ET45, a 18×9.5 ET22 sits 48.4 mm further out at the outer lip and 2.4 mm closer to the suspension at the inner barrel.
Which 1990–1996 Nissan 300ZX wheel and tire upgrade keeps the speedometer most accurate?
Of the 1990–1996 Nissan 300ZX upgrades listed here, 17×8 ET40 · 225/45R17 is closest to the stock 225/50R16, changing overall diameter by +0.5%. At an indicated 60 mph you would actually be doing 60.3 mph.
Do aftermarket wheels need hub-centric rings on a 1990–1996 Nissan 300ZX?
The 1990–1996 Nissan 300ZX's hub bore is 66.1 mm. Wheels machined to exactly 66.1 mm center on the hub directly; wheels with a larger bore need 66.1 mm hub-centric rings to avoid vibration.
Also on 5x114.3
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2003–2008 Nissan 350Z | Z33 | 5x114.3 | 66.1 mm |
| 2009–2020 Nissan 370Z | Z34 | 5x114.3 | 66.1 mm |
| 2009–2024 Nissan GT-R | R35 | 5x114.3 | 66.1 mm |
| 1999–2002 Nissan Skyline GT-R | R34 (BNR34) | 5x114.3 | 66.1 mm |
| 2008–2013 Infiniti G37 Coupe | V36 | 5x114.3 | 66.1 mm |
| 2016–2024 Infiniti Q50 | V37 | 5x114.3 | 66.1 mm |