2021+ Mazda Mazda3 Wheel & Tire Fitment Guide
BP generation, 2.5 Turbo. 5x114.3 bolt pattern, stock 18×7 ET45 on 215/45R18. Compare 3 popular upgrades or try your own size.
Specs
| Bolt pattern | 5x114.3 |
|---|---|
| Center bore | 67.1 mm |
| Lug thread | M12x1.5 |
| Reference trim | 2.5 Turbo |
| Stock wheel | 18×7 ET45 |
| Stock tire | 215/45R18 |
| Stock overall diameter | 25.62 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Mazda Mazda3 2.5 Turbo | ||
|---|---|---|---|
| Bolt pattern | 5x114.3 | Hub bore | 67.1 mm |
| Current | 18×7 ET45, 215/45R18 | New | 18×7 ET45, 215/45R18 |
Popular upgrades
Each size compared with the stock 18×7 ET45, 215/45R18.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| Mild 18×818×8 ET45, 235/40R18 | +12.7 mm | −12.7 mm | −0.8% | 59.5 mph | |
| Flush 18×8.518×8.5 ET35, 235/40R18 | +29 mm | −9.1 mm | −0.8% | 59.5 mph | |
| Aggressive 18×8.518×8.5 ET38, 245/40R18 | +26 mm | −12.1 mm | +0.4% | 60.2 mph |
Shop this setup
I may earn a commission from links on this page.
Searches use the new setup above. Check the bolt pattern, offset and center bore on each listing before you buy, and use hub-centric rings if the wheel's bore is larger than your hub.
Notes
- The 2.5 Turbo sedan and hatch share the 18×7 ET45 wheel (Mazda part 9965C37080 on the sedan) with 215/45R18 89V tires. Mazda specifies 38 psi front and 36 psi rear for the Turbo.
- A 235/40R18 on an 18×8 or 18×8.5 at ET35-45 clears without fender work. Owners report 245/40s rubbing unless the fenders are rolled.
- Wide wheels with high offset can hit the front strut, and a 235/50R17 is reported to rub the lower strut perch.
- Lug nuts are M12×1.5 on a 67.1 mm hub, the same specs as the CX-30.
Questions
What bolt pattern does a 2021+ Mazda Mazda3 use?
The 2021+ Mazda Mazda3 uses a 5x114.3 bolt pattern with a 67.1 mm center bore and M12x1.5 lug threads.
What size wheels and tires are stock on the 2021+ Mazda Mazda3 2.5 Turbo?
The 2021+ Mazda Mazda3 2.5 Turbo came with 18×7 ET45 wheels and 215/45R18 tires, about 25.6 inches in overall diameter.
How far does a 18×8.5 ET35 wheel stick out on a 2021+ Mazda Mazda3?
On the 2021+ Mazda Mazda3, compared with the stock 18×7 ET45, a 18×8.5 ET35 sits 29 mm further out at the outer lip and 9.1 mm closer to the suspension at the inner barrel.
Which 2021+ Mazda Mazda3 wheel and tire upgrade keeps the speedometer most accurate?
Of the 2021+ Mazda Mazda3 upgrades listed here, 18×8.5 ET38 · 245/40R18 is closest to the stock 215/45R18, changing overall diameter by +0.4%. At an indicated 60 mph you would actually be doing 60.2 mph.
Do aftermarket wheels need hub-centric rings on a 2021+ Mazda Mazda3?
The 2021+ Mazda Mazda3's hub bore is 67.1 mm. Wheels machined to exactly 67.1 mm center on the hub directly; wheels with a larger bore need 67.1 mm hub-centric rings to avoid vibration.
Also on 5x114.3
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2010–2013 Mazda Mazdaspeed3 | BL | 5x114.3 | 67.1 mm |
| 2006–2015 Mazda MX-5 Miata | NC | 5x114.3 | 67.1 mm |
| 1993–1995 Mazda RX-7 | FD | 5x114.3 | 67.1 mm |
| 2004–2011 Mazda RX-8 | SE3P | 5x114.3 | 67.1 mm |
| 2019+ Genesis G70 | 1st gen (IK) | 5x114.3 | 67.1 mm |
| 2018–2023 Kia Stinger | CK | 5x114.3 | 67.1 mm |