2004–2011 Mazda RX-8 Wheel & Tire Fitment Guide
SE3P generation, Grand Touring. 5x114.3 bolt pattern, stock 18×8 ET50 on 225/45R18. Compare 3 popular upgrades or try your own size.
Specs
| Bolt pattern | 5x114.3 |
|---|---|
| Center bore | 67.1 mm |
| Lug thread | M12x1.5 |
| Reference trim | Grand Touring |
| Stock wheel | 18×8 ET50 |
| Stock tire | 225/45R18 |
| Stock overall diameter | 25.97 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Mazda RX-8 Grand Touring | ||
|---|---|---|---|
| Bolt pattern | 5x114.3 | Hub bore | 67.1 mm |
| Current | 18×8 ET50, 225/45R18 | New | 18×8 ET50, 225/45R18 |
Popular upgrades
Each size compared with the stock 18×8 ET50, 225/45R18.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| Flush 18×918×9 ET40, 245/40R18 | +22.7 mm | −2.7 mm | −1% | 59.4 mph | |
| Aggressive 18×9.518×9.5 ET35, 255/35R18 | +34 mm | −4 mm | −3.6% | 57.8 mph | |
| Track 17×917×9 ET35, 255/40R17 | +27.7 mm | +2.3 mm | −3.6% | 57.8 mph |
Shop this setup
I may earn a commission from links on this page.
Searches use the new setup above. Check the bolt pattern, offset and center bore on each listing before you buy, and use hub-centric rings if the wheel's bore is larger than your hub.
Notes
- The 18×8 ET50 wheel with 225/45R18 is square on both axles. Some 2004-2008 base cars (mostly automatics) got 16×7.5 or 17×7.5 ET50 wheels, and the 2009-2011 R3 got forged 19×8 ET47 wheels with 225/40R19.
- An 18×9 at ET40-45 with 245/40R18 fits without fender work. Going to 9.5 inches wide at ET30-35 needs the rear fender lips rolled and about -2.5° of camber.
- Lug nuts are M12×1.5 on a 67.1 mm hub, so wheels with a larger bore need hub-centric rings.
Questions
What bolt pattern does a 2004–2011 Mazda RX-8 use?
The 2004–2011 Mazda RX-8 uses a 5x114.3 bolt pattern with a 67.1 mm center bore and M12x1.5 lug threads.
What size wheels and tires are stock on the 2004–2011 Mazda RX-8 Grand Touring?
The 2004–2011 Mazda RX-8 Grand Touring came with 18×8 ET50 wheels and 225/45R18 tires, about 26 inches in overall diameter.
How far does a 18×9.5 ET35 wheel stick out on a 2004–2011 Mazda RX-8?
On the 2004–2011 Mazda RX-8, compared with the stock 18×8 ET50, a 18×9.5 ET35 sits 34 mm further out at the outer lip and 4 mm closer to the suspension at the inner barrel.
Which 2004–2011 Mazda RX-8 wheel and tire upgrade keeps the speedometer most accurate?
Of the 2004–2011 Mazda RX-8 upgrades listed here, 18×9 ET40 · 245/40R18 is closest to the stock 225/45R18, changing overall diameter by −1%. At an indicated 60 mph you would actually be doing 59.4 mph.
Do aftermarket wheels need hub-centric rings on a 2004–2011 Mazda RX-8?
The 2004–2011 Mazda RX-8's hub bore is 67.1 mm. Wheels machined to exactly 67.1 mm center on the hub directly; wheels with a larger bore need 67.1 mm hub-centric rings to avoid vibration.
Also on 5x114.3
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2021+ Mazda Mazda3 | BP | 5x114.3 | 67.1 mm |
| 2010–2013 Mazda Mazdaspeed3 | BL | 5x114.3 | 67.1 mm |
| 2006–2015 Mazda MX-5 Miata | NC | 5x114.3 | 67.1 mm |
| 1993–1995 Mazda RX-7 | FD | 5x114.3 | 67.1 mm |
| 2019+ Genesis G70 | 1st gen (IK) | 5x114.3 | 67.1 mm |
| 2018–2023 Kia Stinger | CK | 5x114.3 | 67.1 mm |