2013–2020 Scion FR-S Wheel & Tire Fitment Guide
ZN6 generation, base. 5x100 bolt pattern, stock 17×7 ET48 on 215/45R17. Compare 3 popular upgrades or try your own size.
Specs
| Bolt pattern | 5x100 |
|---|---|
| Center bore | 56.1 mm |
| Lug thread | M12x1.25 |
| Reference trim | base |
| Stock wheel | 17×7 ET48 |
| Stock tire | 215/45R17 |
| Stock overall diameter | 24.62 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Scion FR-S base | ||
|---|---|---|---|
| Bolt pattern | 5x100 | Hub bore | 56.1 mm |
| Current | 17×7 ET48, 215/45R17 | New | 17×7 ET48, 215/45R17 |
Popular upgrades
Each size compared with the stock 17×7 ET48, 215/45R17.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| Street 18×8.518×8.5 ET35, 235/40R18 | +32 mm | −6.1 mm | +3.2% | 61.9 mph | |
| Flush 17×917×9 ET35, 245/40R17 | +38.4 mm | −12.4 mm | +0.4% | 60.2 mph | |
| Aggressive 18×9.518×9.5 ET40, 265/35R18 | +39.8 mm | −23.8 mm | +2.8% | 61.7 mph |
Shop this setup
I may earn a commission from links on this page.
Searches use the new setup above. Check the bolt pattern, offset and center bore on each listing before you buy, and use hub-centric rings if the wheel's bore is larger than your hub.
Notes
- Stock 17×7 ET48 wheels on 215/45R17 Michelin Primacy HP tires are the same front and rear; the platform is shared with the Subaru BRZ and Toyota 86.
- 17×9 +35 with 245/40R17 is commonly run with at most a slight rear fender roll and about -2° camber; tires wider than 245 usually need rolling.
- 18×9.5 +40 with 265/35R18 has needed front liner trimming and a light roll, with pulled rear fenders.
- 2017+ Toyota 86/BRZ Performance Package cars have Brembo brakes that need 17 in or larger wheels, and some 17×9 +35 designs need about 8 mm spacers to clear them.
Questions
What bolt pattern does a 2013–2020 Scion FR-S use?
The 2013–2020 Scion FR-S uses a 5x100 bolt pattern with a 56.1 mm center bore and M12x1.25 lug threads.
What size wheels and tires are stock on the 2013–2020 Scion FR-S base?
The 2013–2020 Scion FR-S base came with 17×7 ET48 wheels and 215/45R17 tires, about 24.6 inches in overall diameter.
How far does a 18×9.5 ET40 wheel stick out on a 2013–2020 Scion FR-S?
On the 2013–2020 Scion FR-S, compared with the stock 17×7 ET48, a 18×9.5 ET40 sits 39.8 mm further out at the outer lip and 23.8 mm closer to the suspension at the inner barrel.
Which 2013–2020 Scion FR-S wheel and tire upgrade keeps the speedometer most accurate?
Of the 2013–2020 Scion FR-S upgrades listed here, 17×9 ET35 · 245/40R17 is closest to the stock 215/45R17, changing overall diameter by +0.4%. At an indicated 60 mph you would actually be doing 60.2 mph.
Do aftermarket wheels need hub-centric rings on a 2013–2020 Scion FR-S?
The 2013–2020 Scion FR-S's hub bore is 56.1 mm. Wheels machined to exactly 56.1 mm center on the hub directly; wheels with a larger bore need 56.1 mm hub-centric rings to avoid vibration.
Also on 5x100
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2013–2020 Subaru BRZ | ZC6 | 5x100 | 56.1 mm |
| 2022+ Subaru BRZ | ZD8 | 5x100 | 56.1 mm |
| 2011–2014 Subaru WRX | GR/GV | 5x100 | 56.1 mm |
| 2004 Subaru WRX STI | GD | 5x100 | 56.1 mm |
| 2022+ Toyota GR86 | ZN8 | 5x100 | 56.1 mm |
| 2000–2005 Toyota Celica | T230 | 5x100 | 54.1 mm |