2000–2005 Toyota Celica Wheel & Tire Fitment Guide
T230 generation, GT-S. 5x100 bolt pattern, stock 15×6.5 ET39 on 205/55R15. Compare 2 popular upgrades or try your own size.
Specs
| Bolt pattern | 5x100 |
|---|---|
| Center bore | 54.1 mm |
| Lug thread | M12x1.5 |
| Reference trim | GT-S |
| Stock wheel | 15×6.5 ET39 |
| Stock tire | 205/55R15 |
| Stock overall diameter | 23.88 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Toyota Celica GT-S | ||
|---|---|---|---|
| Bolt pattern | 5x100 | Hub bore | 54.1 mm |
| Current | 15×6.5 ET39, 205/55R15 | New | 15×6.5 ET39, 205/55R15 |
Popular upgrades
Each size compared with the stock 15×6.5 ET39, 205/55R15.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| Stock-height 17×7.517×7.5 ET45, 215/45R17 | +6.7 mm | −18.7 mm | +3.1% | 61.9 mph | |
| Lowered 17×7.517×7.5 ET40, 215/40R17 | +11.7 mm | −13.7 mm | −0.4% | 59.7 mph |
Shop this setup
I may earn a commission from links on this page.
Searches use the new setup above. Check the bolt pattern, offset and center bore on each listing before you buy, and use hub-centric rings if the wheel's bore is larger than your hub.
Notes
- US GT-S came standard on 15×6.5 alloys with 205/55R15; the optional 16×6.5 ET39 alloy with 205/50R16 was a cheap option fitted to most cars (and standard on Canadian 2003 GT-S).
- The base GT shares the 5x100 / 54.1 mm hub but ran 195/60R15, with rear drums instead of the GT-S's rear discs.
- Owners report 215/45R17 on 17×7.5 ET45 rubbing the wheel-well liners in hard cornering on stock springs, and 215 width is about the widest commonly run on a lowered car.
Questions
What bolt pattern does a 2000–2005 Toyota Celica use?
The 2000–2005 Toyota Celica uses a 5x100 bolt pattern with a 54.1 mm center bore and M12x1.5 lug threads.
What size wheels and tires are stock on the 2000–2005 Toyota Celica GT-S?
The 2000–2005 Toyota Celica GT-S came with 15×6.5 ET39 wheels and 205/55R15 tires, about 23.9 inches in overall diameter.
How far does a 17×7.5 ET40 wheel stick out on a 2000–2005 Toyota Celica?
On the 2000–2005 Toyota Celica, compared with the stock 15×6.5 ET39, a 17×7.5 ET40 sits 11.7 mm further out at the outer lip and 13.7 mm closer to the suspension at the inner barrel.
Which 2000–2005 Toyota Celica wheel and tire upgrade keeps the speedometer most accurate?
Of the 2000–2005 Toyota Celica upgrades listed here, 17×7.5 ET40 · 215/40R17 is closest to the stock 205/55R15, changing overall diameter by −0.4%. At an indicated 60 mph you would actually be doing 59.7 mph.
Do aftermarket wheels need hub-centric rings on a 2000–2005 Toyota Celica?
The 2000–2005 Toyota Celica's hub bore is 54.1 mm. Wheels machined to exactly 54.1 mm center on the hub directly; wheels with a larger bore need 54.1 mm hub-centric rings to avoid vibration.
Also on 5x100
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2022+ Toyota GR86 | ZN8 | 5x100 | 56.1 mm |
| 2013–2020 Scion FR-S | ZN6 | 5x100 | 56.1 mm |
| 2013–2020 Subaru BRZ | ZC6 | 5x100 | 56.1 mm |
| 2022+ Subaru BRZ | ZD8 | 5x100 | 56.1 mm |
| 2011–2014 Subaru WRX | GR/GV | 5x100 | 56.1 mm |
| 2004 Subaru WRX STI | GD | 5x100 | 56.1 mm |