2000–2005 Volkswagen GTI Wheel & Tire Fitment Guide
Mk4 generation, 1.8T. 5x100 bolt pattern, stock 16×6.5 ET42 on 205/55R16. Compare 2 popular upgrades or try your own size.
Specs
| Bolt pattern | 5x100 |
|---|---|
| Center bore | 57.1 mm |
| Lug thread | M14x1.5 |
| Reference trim | 1.8T |
| Stock wheel | 16×6.5 ET42 |
| Stock tire | 205/55R16 |
| Stock overall diameter | 24.88 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Volkswagen GTI 1.8T | ||
|---|---|---|---|
| Bolt pattern | 5x100 | Hub bore | 57.1 mm |
| Current | 16×6.5 ET42, 205/55R16 | New | 16×6.5 ET42, 205/55R16 |
Popular upgrades
Each size compared with the stock 16×6.5 ET42, 205/55R16.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| OEM+ VR6 17×717×7 ET38, 225/45R17 | +10.3 mm | −2.3 mm | +0.4% | 60.2 mph | |
| Lowered 18×8.518×8.5 ET35, 215/40R18 | +32.4 mm | −18.4 mm | −0.4% | 59.7 mph |
Shop this setup
I may earn a commission from links on this page.
Searches use the new setup above. Check the bolt pattern, offset and center bore on each listing before you buy, and use hub-centric rings if the wheel's bore is larger than your hub.
Notes
- Uses M14x1.5 lug bolts, not studs and nuts; the 5x100 / 57.1 mm hub is shared with the Mk4 Jetta and New Beetle.
- The GTI VR6 came on 225/45R17, and the 337 Edition (2002) and 20th Anniversary (2003) 1.8T came on 18×7.5 wheels (225/45ZR18 and 225/40ZR18 listed).
- Owners running 18×8.5 ET35 on a lowered Mk4 report needing the fenders rolled (and sometimes slightly pulled) to stop rubbing.
Questions
What bolt pattern does a 2000–2005 Volkswagen GTI use?
The 2000–2005 Volkswagen GTI uses a 5x100 bolt pattern with a 57.1 mm center bore and M14x1.5 lug threads.
What size wheels and tires are stock on the 2000–2005 Volkswagen GTI 1.8T?
The 2000–2005 Volkswagen GTI 1.8T came with 16×6.5 ET42 wheels and 205/55R16 tires, about 24.9 inches in overall diameter.
How far does a 18×8.5 ET35 wheel stick out on a 2000–2005 Volkswagen GTI?
On the 2000–2005 Volkswagen GTI, compared with the stock 16×6.5 ET42, a 18×8.5 ET35 sits 32.4 mm further out at the outer lip and 18.4 mm closer to the suspension at the inner barrel.
Which 2000–2005 Volkswagen GTI wheel and tire upgrade keeps the speedometer most accurate?
Of the 2000–2005 Volkswagen GTI upgrades listed here, 17×7 ET38 · 225/45R17 is closest to the stock 205/55R16, changing overall diameter by +0.4%. At an indicated 60 mph you would actually be doing 60.2 mph.
Do aftermarket wheels need hub-centric rings on a 2000–2005 Volkswagen GTI?
The 2000–2005 Volkswagen GTI's hub bore is 57.1 mm. Wheels machined to exactly 57.1 mm center on the hub directly; wheels with a larger bore need 57.1 mm hub-centric rings to avoid vibration.
Also on 5x100
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2013–2020 Scion FR-S | ZN6 | 5x100 | 56.1 mm |
| 2013–2020 Subaru BRZ | ZC6 | 5x100 | 56.1 mm |
| 2022+ Subaru BRZ | ZD8 | 5x100 | 56.1 mm |
| 2011–2014 Subaru WRX | GR/GV | 5x100 | 56.1 mm |
| 2004 Subaru WRX STI | GD | 5x100 | 56.1 mm |
| 2000–2005 Toyota Celica | T230 | 5x100 | 54.1 mm |