2012–2019 Porsche 911 Wheel & Tire Fitment Guide
991 generation, Carrera S. 5x130 bolt pattern, stock 20×8.5 ET51 on 245/35R20. Compare 2 popular upgrades or try your own size.
Specs
| Bolt pattern | 5x130 |
|---|---|
| Center bore | 71.6 mm |
| Lug thread | M14x1.5 |
| Reference trim | Carrera S |
| Stock wheel | 20×8.5 ET51 |
| Stock tire | 245/35R20 |
| Stock overall diameter | 26.75 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Porsche 911 Carrera S | ||
|---|---|---|---|
| Bolt pattern | 5x130 | Hub bore | 71.6 mm |
| Current | 20×8.5 ET51, 245/35R20 | New | 20×8.5 ET51, 245/35R20 |
Popular upgrades
Each size compared with the stock 20×8.5 ET51, 245/35R20.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| Flush 20×920×9 ET44, 245/35R20 | +13.4 mm | +0.6 mm | 0% | 60 mph | |
| Track 19×919×9 ET50, 235/40R19 | +7.4 mm | −5.4 mm | −1.3% | 59.2 mph |
Shop this setup
I may earn a commission from links on this page.
Searches use the new setup above. Check the bolt pattern, offset and center bore on each listing before you buy, and use hub-centric rings if the wheel's bore is larger than your hub.
Notes
- Staggered car. Rear stock on the 991.1: 20×11 ET70 with 295/30ZR20. The 991.2 (2017-2019) rear is 20×11.5 ET76 with 305/30ZR20.
- Uses M14x1.5 lug bolts (160 Nm); hub bore 71.6 mm.
- The C4S/Targa 4S wide-body uses a lower rear offset (ET52 with 305/30ZR20), so rear wheels do not swap with the C2S.
- The Apex 20×9 ET44 front was paired with a 20×11.5 ET72 rear on 305/30R20. The 19-inch track setup pairs 19×9 ET50 front with a 19×11 ET60 rear on 285/35R19.
Questions
What bolt pattern does a 2012–2019 Porsche 911 use?
The 2012–2019 Porsche 911 uses a 5x130 bolt pattern with a 71.6 mm center bore and M14x1.5 lug threads.
What size wheels and tires are stock on the 2012–2019 Porsche 911 Carrera S?
The 2012–2019 Porsche 911 Carrera S came with 20×8.5 ET51 wheels and 245/35R20 tires, about 26.8 inches in overall diameter.
How far does a 20×9 ET44 wheel stick out on a 2012–2019 Porsche 911?
On the 2012–2019 Porsche 911, compared with the stock 20×8.5 ET51, a 20×9 ET44 sits 13.4 mm further out at the outer lip and 0.6 mm further from the suspension at the inner barrel.
Which 2012–2019 Porsche 911 wheel and tire upgrade keeps the speedometer most accurate?
Of the 2012–2019 Porsche 911 upgrades listed here, 20×9 ET44 · 245/35R20 is closest to the stock 245/35R20, changing overall diameter by 0%. At an indicated 60 mph you would actually be doing 60 mph.
Do aftermarket wheels need hub-centric rings on a 2012–2019 Porsche 911?
The 2012–2019 Porsche 911's hub bore is 71.6 mm. Wheels machined to exactly 71.6 mm center on the hub directly; wheels with a larger bore need 71.6 mm hub-centric rings to avoid vibration.
Also on 5x130
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2005–2012 Porsche 911 | 997 | 5x130 | 71.6 mm |
| 2020+ Porsche 911 | 992 | 5x130 | 71.6 mm |
| 2000–2004 Porsche Boxster | 986 | 5x130 | 71.6 mm |
| 2006–2012 Porsche Cayman | 987 | 5x130 | 71.6 mm |
| 2015–2016 Porsche Cayman | 981 | 5x130 | 71.6 mm |