2006–2012 Porsche Cayman Wheel & Tire Fitment Guide
987 generation, S. 5x130 bolt pattern, stock 18×8 ET57 on 235/40R18. Compare 2 popular upgrades or try your own size.
Specs
| Bolt pattern | 5x130 |
|---|---|
| Center bore | 71.6 mm |
| Lug thread | M14x1.5 |
| Reference trim | S |
| Stock wheel | 18×8 ET57 |
| Stock tire | 235/40R18 |
| Stock overall diameter | 25.4 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Porsche Cayman S | ||
|---|---|---|---|
| Bolt pattern | 5x130 | Hub bore | 71.6 mm |
| Current | 18×8 ET57, 235/40R18 | New | 18×8 ET57, 235/40R18 |
Popular upgrades
Each size compared with the stock 18×8 ET57, 235/40R18.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| Wide 18×918×9 ET46, 245/40R18 | +23.7 mm | −1.7 mm | +1.2% | 60.7 mph | |
| Track 18×918×9 ET46, 255/35R18 | +23.7 mm | −1.7 mm | −1.5% | 59.1 mph |
Shop this setup
I may earn a commission from links on this page.
Searches use the new setup above. Check the bolt pattern, offset and center bore on each listing before you buy, and use hub-centric rings if the wheel's bore is larger than your hub.
Notes
- Rear stock: 18×9 ET43 with 265/40R18 (Porsche winter sets use 255/40R18 rear).
- The Cayman S 18×8 ET57 / 18×9 ET43 wheel set is shared with the 987 Boxster S.
- Apex's 18×9 ET46 front / 18×10 ET36 rear set is usually a direct fit with 245/40R18, but 255/35R18 fronts want at least -2° front camber.
- Owners report wider fronts rubbing the inner fender liner as the lower control arm bushings flex; firmer LCA bushings or arms cure it.
Questions
What bolt pattern does a 2006–2012 Porsche Cayman use?
The 2006–2012 Porsche Cayman uses a 5x130 bolt pattern with a 71.6 mm center bore and M14x1.5 lug threads.
What size wheels and tires are stock on the 2006–2012 Porsche Cayman S?
The 2006–2012 Porsche Cayman S came with 18×8 ET57 wheels and 235/40R18 tires, about 25.4 inches in overall diameter.
How far does a 18×9 ET46 wheel stick out on a 2006–2012 Porsche Cayman?
On the 2006–2012 Porsche Cayman, compared with the stock 18×8 ET57, a 18×9 ET46 sits 23.7 mm further out at the outer lip and 1.7 mm closer to the suspension at the inner barrel.
Which 2006–2012 Porsche Cayman wheel and tire upgrade keeps the speedometer most accurate?
Of the 2006–2012 Porsche Cayman upgrades listed here, 18×9 ET46 · 245/40R18 is closest to the stock 235/40R18, changing overall diameter by +1.2%. At an indicated 60 mph you would actually be doing 60.7 mph.
Do aftermarket wheels need hub-centric rings on a 2006–2012 Porsche Cayman?
The 2006–2012 Porsche Cayman's hub bore is 71.6 mm. Wheels machined to exactly 71.6 mm center on the hub directly; wheels with a larger bore need 71.6 mm hub-centric rings to avoid vibration.
Also on 5x130
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2005–2012 Porsche 911 | 997 | 5x130 | 71.6 mm |
| 2012–2019 Porsche 911 | 991 | 5x130 | 71.6 mm |
| 2020+ Porsche 911 | 992 | 5x130 | 71.6 mm |
| 2000–2004 Porsche Boxster | 986 | 5x130 | 71.6 mm |
| 2015–2016 Porsche Cayman | 981 | 5x130 | 71.6 mm |