2000–2004 Porsche Boxster Wheel & Tire Fitment Guide
986 generation, S. 5x130 bolt pattern, stock 17×7 ET55 on 205/50R17. Compare 2 popular upgrades or try your own size.
Specs
| Bolt pattern | 5x130 |
|---|---|
| Center bore | 71.6 mm |
| Lug thread | M14x1.5 |
| Reference trim | S |
| Stock wheel | 17×7 ET55 |
| Stock tire | 205/50R17 |
| Stock overall diameter | 25.07 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Porsche Boxster S | ||
|---|---|---|---|
| Bolt pattern | 5x130 | Hub bore | 71.6 mm |
| Current | 17×7 ET55, 205/50R17 | New | 17×7 ET55, 205/50R17 |
Popular upgrades
Each size compared with the stock 17×7 ET55, 205/50R17.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| Turbo Look 18×818×8 ET50, 225/40R18 | +17.7 mm | −7.7 mm | +0.1% | 60 mph | |
| Track 18×918×9 ET46, 245/40R18 | +34.4 mm | −16.4 mm | +2.6% | 61.5 mph |
Shop this setup
I may earn a commission from links on this page.
Searches use the new setup above. Check the bolt pattern, offset and center bore on each listing before you buy, and use hub-centric rings if the wheel's bore is larger than your hub.
Notes
- Rear stock: 17×8.5 ET50 with 255/40R17.
- The 17-inch set was standard on the S; base Boxsters came on 16s with 17s optional.
- Porsche Tequipment 18×8 ET50 / 18×10 ET47 sets (225/40R18 / 265/35R18) bolt on without modification.
- Apex's 18×9 ET46 / 18×10 ET36 track set (245/40R18 / 275/35R18) generally needs added front negative camber via camber plates.
Questions
What bolt pattern does a 2000–2004 Porsche Boxster use?
The 2000–2004 Porsche Boxster uses a 5x130 bolt pattern with a 71.6 mm center bore and M14x1.5 lug threads.
What size wheels and tires are stock on the 2000–2004 Porsche Boxster S?
The 2000–2004 Porsche Boxster S came with 17×7 ET55 wheels and 205/50R17 tires, about 25.1 inches in overall diameter.
How far does a 18×9 ET46 wheel stick out on a 2000–2004 Porsche Boxster?
On the 2000–2004 Porsche Boxster, compared with the stock 17×7 ET55, a 18×9 ET46 sits 34.4 mm further out at the outer lip and 16.4 mm closer to the suspension at the inner barrel.
Which 2000–2004 Porsche Boxster wheel and tire upgrade keeps the speedometer most accurate?
Of the 2000–2004 Porsche Boxster upgrades listed here, 18×8 ET50 · 225/40R18 is closest to the stock 205/50R17, changing overall diameter by +0.1%. At an indicated 60 mph you would actually be doing 60 mph.
Do aftermarket wheels need hub-centric rings on a 2000–2004 Porsche Boxster?
The 2000–2004 Porsche Boxster's hub bore is 71.6 mm. Wheels machined to exactly 71.6 mm center on the hub directly; wheels with a larger bore need 71.6 mm hub-centric rings to avoid vibration.
Also on 5x130
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2005–2012 Porsche 911 | 997 | 5x130 | 71.6 mm |
| 2012–2019 Porsche 911 | 991 | 5x130 | 71.6 mm |
| 2020+ Porsche 911 | 992 | 5x130 | 71.6 mm |
| 2006–2012 Porsche Cayman | 987 | 5x130 | 71.6 mm |
| 2015–2016 Porsche Cayman | 981 | 5x130 | 71.6 mm |