2020+ Porsche 911 Wheel & Tire Fitment Guide
992 generation, Carrera. 5x130 bolt pattern, stock 19×8.5 ET52 on 235/40R19. Compare 2 popular upgrades or try your own size.
Specs
| Bolt pattern | 5x130 |
|---|---|
| Center bore | 71.6 mm |
| Lug thread | M14x1.5 |
| Reference trim | Carrera |
| Stock wheel | 19×8.5 ET52 |
| Stock tire | 235/40R19 |
| Stock overall diameter | 26.4 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Porsche 911 Carrera | ||
|---|---|---|---|
| Bolt pattern | 5x130 | Hub bore | 71.6 mm |
| Current | 19×8.5 ET52, 235/40R19 | New | 19×8.5 ET52, 235/40R19 |
Popular upgrades
Each size compared with the stock 19×8.5 ET52, 235/40R19.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| OEM Carrera S 20×8.520×8.5 ET53, 245/35R20 | −1 mm | −1 mm | +1.3% | 60.8 mph | |
| Flush 20×920×9 ET41, 245/35R20 | +17.4 mm | +4.6 mm | +1.3% | 60.8 mph |
Shop this setup
I may earn a commission from links on this page.
Searches use the new setup above. Check the bolt pattern, offset and center bore on each listing before you buy, and use hub-centric rings if the wheel's bore is larger than your hub.
Notes
- Rear stock: 20×11.5 ET67 with 295/35R20; Porsche's winter set uses a narrower 20×11 ET66 rear.
- Carrera S and Carrera wheels share the hub, so the S's 20×8.5 ET53 / 21×11.5 ET67 set (245/35R20, 305/30R21) bolts straight on.
- Wheels are held by M14x1.5 lug bolts, not studs and nuts; GTS cars with optional center-lock hubs cannot use five-bolt wheels.
- A popular aftermarket staggered setup is 20×9 ET41 front with 21×11.5 ET58 rear; Apex notes cars with front-axle lift may need a 5 mm front spacer for some combinations.
Questions
What bolt pattern does a 2020+ Porsche 911 use?
The 2020+ Porsche 911 uses a 5x130 bolt pattern with a 71.6 mm center bore and M14x1.5 lug threads.
What size wheels and tires are stock on the 2020+ Porsche 911 Carrera?
The 2020+ Porsche 911 Carrera came with 19×8.5 ET52 wheels and 235/40R19 tires, about 26.4 inches in overall diameter.
How far does a 20×9 ET41 wheel stick out on a 2020+ Porsche 911?
On the 2020+ Porsche 911, compared with the stock 19×8.5 ET52, a 20×9 ET41 sits 17.4 mm further out at the outer lip and 4.6 mm further from the suspension at the inner barrel.
Which 2020+ Porsche 911 wheel and tire upgrade keeps the speedometer most accurate?
Of the 2020+ Porsche 911 upgrades listed here, 20×8.5 ET53 · 245/35R20 is closest to the stock 235/40R19, changing overall diameter by +1.3%. At an indicated 60 mph you would actually be doing 60.8 mph.
Do aftermarket wheels need hub-centric rings on a 2020+ Porsche 911?
The 2020+ Porsche 911's hub bore is 71.6 mm. Wheels machined to exactly 71.6 mm center on the hub directly; wheels with a larger bore need 71.6 mm hub-centric rings to avoid vibration.
Also on 5x130
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2005–2012 Porsche 911 | 997 | 5x130 | 71.6 mm |
| 2012–2019 Porsche 911 | 991 | 5x130 | 71.6 mm |
| 2000–2004 Porsche Boxster | 986 | 5x130 | 71.6 mm |
| 2006–2012 Porsche Cayman | 987 | 5x130 | 71.6 mm |
| 2015–2016 Porsche Cayman | 981 | 5x130 | 71.6 mm |