2007–2014 Toyota FJ Cruiser Wheel & Tire Fitment Guide
XJ10 generation, Base. 6x139.7 bolt pattern, stock 17×7.5 ET15 on 265/70R17. Compare 2 popular upgrades or try your own size.
Specs
| Bolt pattern | 6x139.7 |
|---|---|
| Center bore | 106.1 mm |
| Lug thread | M12x1.5 |
| Reference trim | Base |
| Stock wheel | 17×7.5 ET15 |
| Stock tire | 265/70R17 |
| Stock overall diameter | 31.61 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Toyota FJ Cruiser Base | ||
|---|---|---|---|
| Bolt pattern | 6x139.7 | Hub bore | 106.1 mm |
| Current | 17×7.5 ET15, 265/70R17 | New | 17×7.5 ET15, 265/70R17 |
Popular upgrades
Each size compared with the stock 17×7.5 ET15, 265/70R17.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| Skinny 33 on stock wheel17×7.5 ET15, 255/80R17 | 0 mm | 0 mm | +4.6% | 62.8 mph | |
| 285/70R17 + 2in level17×7.5 ET15, 285/70R17 | 0 mm | 0 mm | +3.5% | 62.1 mph |
Shop this setup
I may earn a commission from links on this page.
Searches use the new setup above. Check the bolt pattern, offset and center bore on each listing before you buy, and use hub-centric rings if the wheel's bore is larger than your hub.
Notes
- Base trucks came on 17x7.5 ET15 wheels (black 16-hole steel or alloy) with 265/70R17; the off-road/Trail Teams packages used 16-inch wheels with 265/75R16.
- Shares 6x139.7, the 106.1 mm bore and M12x1.5 lug nuts with the 4th/5th-gen 4Runner, GX470 and 2nd-gen Tacoma, and FJ wheels are a common swap onto those trucks.
- 255/80R17 (about 33 in) is reported to fit at stock height with no rubbing; wider 285s on the positive-offset stock wheel can contact the upper control arm and body mount at full lock.
- Tuff Country and similar 2-inch front leveling kits list 285/70R17 as their recommended tire.
Questions
What bolt pattern does a 2007–2014 Toyota FJ Cruiser use?
The 2007–2014 Toyota FJ Cruiser uses a 6x139.7 bolt pattern with a 106.1 mm center bore and M12x1.5 lug threads.
What size wheels and tires are stock on the 2007–2014 Toyota FJ Cruiser Base?
The 2007–2014 Toyota FJ Cruiser Base came with 17×7.5 ET15 wheels and 265/70R17 tires, about 31.6 inches in overall diameter.
How far does a 17×7.5 ET15 wheel stick out on a 2007–2014 Toyota FJ Cruiser?
On the 2007–2014 Toyota FJ Cruiser, compared with the stock 17×7.5 ET15, a 17×7.5 ET15 sits 0 mm further out at the outer lip and in the same place at the inner barrel.
Which 2007–2014 Toyota FJ Cruiser wheel and tire upgrade keeps the speedometer most accurate?
Of the 2007–2014 Toyota FJ Cruiser upgrades listed here, 17×7.5 ET15 · 285/70R17 is closest to the stock 265/70R17, changing overall diameter by +3.5%. At an indicated 60 mph you would actually be doing 62.1 mph.
Do aftermarket wheels need hub-centric rings on a 2007–2014 Toyota FJ Cruiser?
The 2007–2014 Toyota FJ Cruiser's hub bore is 106.1 mm. Wheels machined to exactly 106.1 mm center on the hub directly; wheels with a larger bore need 106.1 mm hub-centric rings to avoid vibration.
Also on 6x139.7
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2005–2015 Toyota Tacoma | 2nd gen | 6x139.7 | 106.1 mm |
| 2016–2023 Toyota Tacoma | 3rd gen | 6x139.7 | 106.1 mm |
| 2021+ Ford Bronco | 6th gen (U725) | 6x139.7 | 93.1 mm |
| 2024+ Ford Ranger Raptor | P703 | 6x139.7 | 93.1 mm |
| 2025+ Toyota 4Runner | 6th gen | 6x139.7 | 95.1 mm |
| 2024+ Toyota Tacoma | 4th gen | 6x139.7 | 95.1 mm |