2005–2015 Toyota Tacoma Wheel & Tire Fitment Guide
2nd gen generation, TRD Off-Road. 6x139.7 bolt pattern, stock 16×7 ET30 on 265/70R16. Compare 2 popular upgrades or try your own size.
Specs
| Bolt pattern | 6x139.7 |
|---|---|
| Center bore | 106.1 mm |
| Lug thread | M12x1.5 |
| Reference trim | TRD Off-Road |
| Stock wheel | 16×7 ET30 |
| Stock tire | 265/70R16 |
| Stock overall diameter | 30.61 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Toyota Tacoma TRD Off-Road | ||
|---|---|---|---|
| Bolt pattern | 6x139.7 | Hub bore | 106.1 mm |
| Current | 16×7 ET30, 265/70R16 | New | 16×7 ET30, 265/70R16 |
Popular upgrades
Each size compared with the stock 16×7 ET30, 265/70R16.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| Stock wheel 265/75R1616×7 ET30, 265/75R16 | 0 mm | 0 mm | +3.4% | 62 mph | |
| Lifted 16×8 ET016×8 ET0, 285/75R16 | +42.7 mm | +17.3 mm | +7.3% | 64.4 mph |
Shop this setup
I may earn a commission from links on this page.
Searches use the new setup above. Check the bolt pattern, offset and center bore on each listing before you buy, and use hub-centric rings if the wheel's bore is larger than your hub.
Notes
- 6x139.7 / 106.1 mm applies to 4WD and PreRunner trucks; 2WD non-PreRunner trucks (including X-Runner) use 5x114.3 with a 60.1 mm bore.
- The TRD Off-Road wheel is 16×7 ET30 (part 42611-AD031); the TRD Sport ran 17×7.5 ET30 with 265/65R17.
- 265/75R16 fits the stock TRD Off-Road wheel with no lift, with the front mud flaps the usual rub point.
- 285/75R16 on 16×8 ET0 generally needs a 2-3 in lift and often a cab mount chop plus inner fender/flare trimming to stop rubbing at full lock.
Questions
What bolt pattern does a 2005–2015 Toyota Tacoma use?
The 2005–2015 Toyota Tacoma uses a 6x139.7 bolt pattern with a 106.1 mm center bore and M12x1.5 lug threads.
What size wheels and tires are stock on the 2005–2015 Toyota Tacoma TRD Off-Road?
The 2005–2015 Toyota Tacoma TRD Off-Road came with 16×7 ET30 wheels and 265/70R16 tires, about 30.6 inches in overall diameter.
How far does a 16×8 ET0 wheel stick out on a 2005–2015 Toyota Tacoma?
On the 2005–2015 Toyota Tacoma, compared with the stock 16×7 ET30, a 16×8 ET0 sits 42.7 mm further out at the outer lip and 17.3 mm further from the suspension at the inner barrel.
Which 2005–2015 Toyota Tacoma wheel and tire upgrade keeps the speedometer most accurate?
Of the 2005–2015 Toyota Tacoma upgrades listed here, 16×7 ET30 · 265/75R16 is closest to the stock 265/70R16, changing overall diameter by +3.4%. At an indicated 60 mph you would actually be doing 62 mph.
Do aftermarket wheels need hub-centric rings on a 2005–2015 Toyota Tacoma?
The 2005–2015 Toyota Tacoma's hub bore is 106.1 mm. Wheels machined to exactly 106.1 mm center on the hub directly; wheels with a larger bore need 106.1 mm hub-centric rings to avoid vibration.
Also on 6x139.7
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2007–2014 Toyota FJ Cruiser | XJ10 | 6x139.7 | 106.1 mm |
| 2016–2023 Toyota Tacoma | 3rd gen | 6x139.7 | 106.1 mm |
| 2021+ Ford Bronco | 6th gen (U725) | 6x139.7 | 93.1 mm |
| 2024+ Ford Ranger Raptor | P703 | 6x139.7 | 93.1 mm |
| 2025+ Toyota 4Runner | 6th gen | 6x139.7 | 95.1 mm |
| 2024+ Toyota Tacoma | 4th gen | 6x139.7 | 95.1 mm |