2025+ Toyota 4Runner Wheel & Tire Fitment Guide
6th gen generation, TRD Off-Road. 6x139.7 bolt pattern, stock 18×7.5 ET55 on 265/70R18. Compare 2 popular upgrades or try your own size.
Specs
| Bolt pattern | 6x139.7 |
|---|---|
| Center bore | 95.1 mm |
| Lug thread | M14x1.5 |
| Reference trim | TRD Off-Road |
| Stock wheel | 18×7.5 ET55 |
| Stock tire | 265/70R18 |
| Stock overall diameter | 32.61 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Toyota 4Runner TRD Off-Road | ||
|---|---|---|---|
| Bolt pattern | 6x139.7 | Hub bore | 95.1 mm |
| Current | 18×7.5 ET55, 265/70R18 | New | 18×7.5 ET55, 265/70R18 |
Popular upgrades
Each size compared with the stock 18×7.5 ET55, 265/70R18.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| 33in on 17×8.5 +35, no lift17×8.5 ET35, 285/70R17 | +32.7 mm | +7.3 mm | +0.3% | 60.2 mph | |
| Lifted 17×8.5 ET0, 285/7017×8.5 ET0, 285/70R17 | +67.7 mm | +42.3 mm | +0.3% | 60.2 mph |
Shop this setup
I may earn a commission from links on this page.
Searches use the new setup above. Check the bolt pattern, offset and center bore on each listing before you buy, and use hub-centric rings if the wheel's bore is larger than your hub.
Notes
- The 6th gen uses the TNGA-F hub (95.1 mm bore, M14x1.5 lugs) shared with the 2024+ Tacoma and 2022+ Tundra; 5th-gen 4Runner wheels (106.1 mm bore, M12 lugs) need hub rings and different lug nuts.
- The TRD Off-Road's 18x7.5 ET55 wheel is reported to be the same wheel as the 18-inch 2024+ Tacoma's; 17-inch wheels clear the brakes (the SR5 runs 17x7.5).
- Owners report 285/70R17 on Method 703 17x8.5 +35 fits the TRD Off-Road Premium on stock suspension with no rubbing, sitting near flush with the flares.
- More aggressive 17x8.5 ET0 with 285/70R17 has been run on a ReadyLift 2.5 in front / 1 in rear kit, and 285/75R17 on +35 wheels with a 2.5 in TRD lift.
Questions
What bolt pattern does a 2025+ Toyota 4Runner use?
The 2025+ Toyota 4Runner uses a 6x139.7 bolt pattern with a 95.1 mm center bore and M14x1.5 lug threads.
What size wheels and tires are stock on the 2025+ Toyota 4Runner TRD Off-Road?
The 2025+ Toyota 4Runner TRD Off-Road came with 18×7.5 ET55 wheels and 265/70R18 tires, about 32.6 inches in overall diameter.
How far does a 17×8.5 ET0 wheel stick out on a 2025+ Toyota 4Runner?
On the 2025+ Toyota 4Runner, compared with the stock 18×7.5 ET55, a 17×8.5 ET0 sits 67.7 mm further out at the outer lip and 42.3 mm further from the suspension at the inner barrel.
Which 2025+ Toyota 4Runner wheel and tire upgrade keeps the speedometer most accurate?
Of the 2025+ Toyota 4Runner upgrades listed here, 17×8.5 ET35 · 285/70R17 is closest to the stock 265/70R18, changing overall diameter by +0.3%. At an indicated 60 mph you would actually be doing 60.2 mph.
Do aftermarket wheels need hub-centric rings on a 2025+ Toyota 4Runner?
The 2025+ Toyota 4Runner's hub bore is 95.1 mm. Wheels machined to exactly 95.1 mm center on the hub directly; wheels with a larger bore need 95.1 mm hub-centric rings to avoid vibration.
Also on 6x139.7
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2024+ Toyota Tacoma | 4th gen | 6x139.7 | 95.1 mm |
| 2021–2024 Ram 1500 TRX | DT | 6x139.7 | 77.8 mm |
| 2007–2014 Toyota FJ Cruiser | XJ10 | 6x139.7 | 106.1 mm |
| 2005–2015 Toyota Tacoma | 2nd gen | 6x139.7 | 106.1 mm |
| 2016–2023 Toyota Tacoma | 3rd gen | 6x139.7 | 106.1 mm |
| 2021+ Ford Bronco | 6th gen (U725) | 6x139.7 | 93.1 mm |