2024+ Toyota Tacoma Wheel & Tire Fitment Guide
4th gen generation, TRD Off-Road. 6x139.7 bolt pattern, stock 17×7.5 ET55 on 265/70R17. Compare 2 popular upgrades or try your own size.
Specs
| Bolt pattern | 6x139.7 |
|---|---|
| Center bore | 95.1 mm |
| Lug thread | M14x1.5 |
| Reference trim | TRD Off-Road |
| Stock wheel | 17×7.5 ET55 |
| Stock tire | 265/70R17 |
| Stock overall diameter | 31.61 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Toyota Tacoma TRD Off-Road | ||
|---|---|---|---|
| Bolt pattern | 6x139.7 | Hub bore | 95.1 mm |
| Current | 17×7.5 ET55, 265/70R17 | New | 17×7.5 ET55, 265/70R17 |
Popular upgrades
Each size compared with the stock 17×7.5 ET55, 265/70R17.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| 33in on 17×8 +20, no lift17×8 ET20, 285/70R17 | +41.3 mm | +28.7 mm | +3.5% | 62.1 mph | |
| 35in on 17×8 +25, lifted17×8 ET25, 315/70R17 | +36.3 mm | +23.7 mm | +8.7% | 65.2 mph |
Shop this setup
I may earn a commission from links on this page.
Searches use the new setup above. Check the bolt pattern, offset and center bore on each listing before you buy, and use hub-centric rings if the wheel's bore is larger than your hub.
Notes
- The 4th gen moved to the TNGA-F hub: 95.1 mm bore and M14x1.5 lugs, shared with the 2022+ Tundra and 2025+ 4Runner; 3rd-gen Tacoma wheels (106.1 mm bore) need 106.1-to-95.1 hub rings and M14 nuts.
- Owners report the OEM lug nuts do not seat on conical-seat aftermarket wheels, so buy matching M14x1.5 conical nuts.
- 285/70R17 on stock suspension works for some owners, but others report rubbing the front liner at full lock and under compression; alignment (caster) is often blamed.
- The 35-inch setup (35x12.50R17, about 315/70R17) is reported with a 2.5 in front lift and removal of the front safety bracket. Other trims: SR/SR5 17x7 ET60 with 245/70R17, TRD Pro 18x8.5 ET20 with 265/70R18.
Questions
What bolt pattern does a 2024+ Toyota Tacoma use?
The 2024+ Toyota Tacoma uses a 6x139.7 bolt pattern with a 95.1 mm center bore and M14x1.5 lug threads.
What size wheels and tires are stock on the 2024+ Toyota Tacoma TRD Off-Road?
The 2024+ Toyota Tacoma TRD Off-Road came with 17×7.5 ET55 wheels and 265/70R17 tires, about 31.6 inches in overall diameter.
How far does a 17×8 ET20 wheel stick out on a 2024+ Toyota Tacoma?
On the 2024+ Toyota Tacoma, compared with the stock 17×7.5 ET55, a 17×8 ET20 sits 41.3 mm further out at the outer lip and 28.7 mm further from the suspension at the inner barrel.
Which 2024+ Toyota Tacoma wheel and tire upgrade keeps the speedometer most accurate?
Of the 2024+ Toyota Tacoma upgrades listed here, 17×8 ET20 · 285/70R17 is closest to the stock 265/70R17, changing overall diameter by +3.5%. At an indicated 60 mph you would actually be doing 62.1 mph.
Do aftermarket wheels need hub-centric rings on a 2024+ Toyota Tacoma?
The 2024+ Toyota Tacoma's hub bore is 95.1 mm. Wheels machined to exactly 95.1 mm center on the hub directly; wheels with a larger bore need 95.1 mm hub-centric rings to avoid vibration.
Also on 6x139.7
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2025+ Toyota 4Runner | 6th gen | 6x139.7 | 95.1 mm |
| 2021–2024 Ram 1500 TRX | DT | 6x139.7 | 77.8 mm |
| 2007–2014 Toyota FJ Cruiser | XJ10 | 6x139.7 | 106.1 mm |
| 2005–2015 Toyota Tacoma | 2nd gen | 6x139.7 | 106.1 mm |
| 2016–2023 Toyota Tacoma | 3rd gen | 6x139.7 | 106.1 mm |
| 2021+ Ford Bronco | 6th gen (U725) | 6x139.7 | 93.1 mm |