2021–2024 Ram 1500 TRX Wheel & Tire Fitment Guide
DT generation, base. 6x139.7 bolt pattern, stock 18×9 ET19 on 325/65R18. Compare 2 popular upgrades or try your own size.
Specs
| Bolt pattern | 6x139.7 |
|---|---|
| Center bore | 77.8 mm |
| Lug thread | M14x1.5 |
| Reference trim | base |
| Stock wheel | 18×9 ET19 |
| Stock tire | 325/65R18 |
| Stock overall diameter | 34.63 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Ram 1500 TRX base | ||
|---|---|---|---|
| Bolt pattern | 6x139.7 | Hub bore | 77.8 mm |
| Current | 18×9 ET19, 325/65R18 | New | 18×9 ET19, 325/65R18 |
Popular upgrades
Each size compared with the stock 18×9 ET19, 325/65R18.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| 18×9 ET0, stock 35s18×9 ET0, 325/65R18 | +19 mm | +19 mm | 0% | 60 mph | |
| 37s on stock 18×918×9 ET19, 315/75R18 | 0 mm | 0 mm | +5.7% | 63.4 mph |
Shop this setup
I may earn a commission from links on this page.
Searches use the new setup above. Check the bolt pattern, offset and center bore on each listing before you buy, and use hub-centric rings if the wheel's bore is larger than your hub.
Notes
- Stock tire is LT325/65R18 (Goodyear Wrangler Territory A/T, about 35 in tall) on 18×9 wheels at +19 mm (0.75 in).
- Lug nuts are M14x1.5 on a 6x139.7 pattern with a 77.8 mm hub, the same as other DT Ram 1500s.
- Owners report 37x12.5R18 tires fitting on stock wheels and suspension with little or no rub on-road; 37x12.5R18 is listed here as the nearest metric size, 315/75R18.
- Lower-offset wheels (around -10 mm) with 37s have been reported to rub slightly at full lock.
Questions
What bolt pattern does a 2021–2024 Ram 1500 TRX use?
The 2021–2024 Ram 1500 TRX uses a 6x139.7 bolt pattern with a 77.8 mm center bore and M14x1.5 lug threads.
What size wheels and tires are stock on the 2021–2024 Ram 1500 TRX base?
The 2021–2024 Ram 1500 TRX base came with 18×9 ET19 wheels and 325/65R18 tires, about 34.6 inches in overall diameter.
How far does a 18×9 ET0 wheel stick out on a 2021–2024 Ram 1500 TRX?
On the 2021–2024 Ram 1500 TRX, compared with the stock 18×9 ET19, a 18×9 ET0 sits 19 mm further out at the outer lip and 19 mm further from the suspension at the inner barrel.
Which 2021–2024 Ram 1500 TRX wheel and tire upgrade keeps the speedometer most accurate?
Of the 2021–2024 Ram 1500 TRX upgrades listed here, 18×9 ET0 · 325/65R18 is closest to the stock 325/65R18, changing overall diameter by 0%. At an indicated 60 mph you would actually be doing 60 mph.
Do aftermarket wheels need hub-centric rings on a 2021–2024 Ram 1500 TRX?
The 2021–2024 Ram 1500 TRX's hub bore is 77.8 mm. Wheels machined to exactly 77.8 mm center on the hub directly; wheels with a larger bore need 77.8 mm hub-centric rings to avoid vibration.
Also on 6x139.7
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2025+ Toyota 4Runner | 6th gen | 6x139.7 | 95.1 mm |
| 2024+ Toyota Tacoma | 4th gen | 6x139.7 | 95.1 mm |
| 2021+ Ford Bronco | 6th gen (U725) | 6x139.7 | 93.1 mm |
| 2024+ Ford Ranger Raptor | P703 | 6x139.7 | 93.1 mm |
| 2007–2014 Toyota FJ Cruiser | XJ10 | 6x139.7 | 106.1 mm |
| 2005–2015 Toyota Tacoma | 2nd gen | 6x139.7 | 106.1 mm |